
Planning smart home features before your renovation begins is essential because walls, ceilings, and electrical lines are still exposed, making concealed wiring, structured cabling, networking, and sensor placement easier and cleaner. Those conveniences are easier to build in when we plan them alongside the new layout. Before the walls, ceilings and floors are finished, we can run cables, add outlets and leave room for equipment we might but later.
Key Takeaways
- Mark where you’ll need Wi-Fi, power and controls on the renovation plans before work starts.
- Coordinate lighting, heating, shades and security with the trades already working in those rooms.
- Install hard-to-reach wiring and conduit first. Choose replaceable devices as the budget allows.
Plan Ethernet and Wi-Fi Around the New Layout
Start with the places we’ll actually use the network. A lawn office needs a trustworthy connection for video calls, while a living room might need Ethernet for a TV and game comfort. Mark those locations on the floor plan along with ceiling or wall positions for wireless approach points. An extension, a masonry wall or a practicality cupboard at one end of the house can leave an otherwise capable networking too far from the rooms it needs to serve.
Run Ethernet cables back to an available, ventilated spot with power for the router and network switch. If you plan to buy wireless access point hardware for a new expansion or home office, decide where each unit will go and confirm its power requirements before the walls close. A consistent Power over Ethernet switch can supply both power and data through the same cable, so you won’t need a separate power supply at each access point. Ask your installer which cable suits the planned runs and whether to leave an additional connection for future extension.
Design Smart Lighting and Motorised Shades Together
Think through the instants we want the room to handle. In an open-plan kitchen, we might want bright task lighting over the worktop, softer charm over the table and a low setting for walking across at night. Put those fixtures on separate controls so that one scene can dim the pendants while leaving the countertop lights on. Keep physical switches or keypads where family members and guests expect to find them.
Ask the electrician to check dimmer and fixture harmony before ordering, especially for integrated LED fixtures. Smart dimmers differ in their wiring requirements, and some models can work without an objective at the switch. If you’re deliberating motorised shades, decide where they’ll sit and how they’ll get power before fitting window trim or closing a intended pocket. Leave enough approach to service the motor later.
Coordinate Smart Thermostats With Heating and Cooling
A restored home can have rooms that heat and cool at different rates. A sunny expansion might stay warm into the evening while an upstairs bedroom cools quickly. If we want separate temperature schedules, ask the HVAC builder whether the planned system can control those areas separately. This is the time to discuss regulator and sensor locations, underfloor heating controls, and wiring. For a heat pump or a system with its own interact controls, confirm concord before buying a thermostat. Have the contractor check the available wiring and whether the chosen model needs a common wire or an accessory.
Prepare for Smart Security, Leak Detection and Entertainment
- Entry and cameras. Choose doorbell and camera locations using the finished layout. Check what the camera will see once stoop lights, fencing and landscaping are in place. If you want to give a carrier a temporary code, confirm that the lock supports deadline access and fits the door hardware.
- Leak detection. Place sensing where a small leak could go unnoticed, such as under the washer or near the water heater. If you want an automatic shutoff, ask the roofer to allow space and service access near the main water line.
- TV and audio. Mark the screen, soundbar, and speaker positions on the plans. Run speaker cable while the canopy is open and contemplate an intermediary between the TV and equipment cabinet so a future cable can be replaced without decreasing the wall.
FAQs
What should we check before the walls close?
Walk the site with the installer and compare every cable, exit and switch position with the latest plans. Ask for terminated cable ends, test results, and photos of hidden routes. Check that spare tubes have pull cords and accessible ends.
Do we need to choose a smart home platform now?
We can usually defer the choice of hub and plug-in devices. Verify wiring requirements early for any hardwired controls you already have in mind. When shopping later, check whether authorized devices support the specific features you want in your chosen app, including what you can control when you’re away from home.



